Differential Rearmable or with automatic reconnection of 2P, 40A, 30 mA (2x40x30 mA) of the GEWISS brand.

This PRO version of GEWISS stands out for:

• Before reassembling, check the installation and only rearm if everything is correct and there are no ground connections, thus achieving maximum safety for people and equipment.
• This installation check is done every 2 minutes an unlimited number of times and without blocking, rearming only when it has detected that the safety conditions have been restored. That is, it has an unlimited number of rearms.
• The rearmament is motorized, if the installation is safe, it rearms in less than 10 seconds after the trip.

This Rearmable differential allows maximum safety and continuity of service, thanks to its innovative isolation control system, the rearmable differential reclosers allow reconnection in conditions of optimal safety for people, both in residential and tertiary applications.

When the differential switch trips, ReStart performs insulation control before automatic reset. In the event of a ground fault, ReStart does not reset the switch.

In case of differential firing (storms, humidity, sympathetic firing, etc.), the resettable differential will reconnect the installation only if the defect has disappeared, guaranteeing the safety of people and the installation.

Technical characteristics:

• Number of poles: 2 Poles - equivalent to 3 modules
• Rated rated current: 40 A
• Rated operating voltage in alternating: 230 V
• Rated frequency: 50/60 Hz
• Connection Type: Screw Cage
• Flexible cable connection section: 16 mm

Reference. GEWISS GWD4827P

Technical Characteristics:

Reference. HAGER CDA240SC

Differential automatic reconnection Rearmable or 2P, 40A, 30 mA (2x40x30 mA) RED brand series Schneider.

This differential Rearmable allows maximum safety and continuity of service, thanks to its innovative control system insulation, differential reclosers RED reconnect allow optimum safety conditions for people, both residential and tertiary applications.

Technical Characteristics:

• Number of Poles: 2 Poles
• Neutral pole position: Left
• [In] rated current: 40 A
• Earthing system TN-S TT
• Network Type: AC
• Earth leakage sensitivity: 30 mA
• Location device system: Departure
• Rated operating frequency: 50 Hz
• [Ue] aisgnada voltage: 230 V AC 50 Hz phase to neutral
• Reset: Reset earth leakage faults
• Test function: Manual 100 V
• Protec.pérdida ground delay time: Instant
• Type earth leakage protection: Class A
• Leakage resistance: 16 kOhm aloperar - 8kOhm en no operativo
• Cutting capacity and nominal fechamento: IDM 630 to 230 V
• [Ui] rated insulation voltage: 500 V
• [Uimp] rated impulse voltage: 4 kV
• Control Type: Lever
• Local signs: 1 LED verde/rojo - Dispositivo diferencial: señalización ON/OFF - Reconectador: señalización ON/OFF
• Operating mode: Reclose time: 10 s, Maximum operating frequency: 30/hour, Maximum number of consecutive restarts: 3, Minimum interval between 2 closures: 180 s, Insulation fault presence monitoring, Restart cycle stop if insulation fault present, Restart on transient insulation fault.
• Signalling circuit voltage: DC: 5 ... 230 V - CA: 5 ... 230 V
• Mounting mode Fixed
• Mounting options: DIN rail 35mm
• Steps 9 mm: 6
• Dimensions: height 106 mm - Width 54 mm - Depth 82 mm
• Mechanical endurance: 4000 cycles open-close
• Standards: EN 61008 - IEC 61008
• IP Grade: IP20

Reference. SCHNEIDER A9CR4240

Differential 2P, 40A, 30 mA, with automatic reconnection REC 4 series, to ensure continuity of electric service to unforeseen situations that cause tripping.

A circuit breaker associated with an intelligent engine reconnection, which enables safe reconnection to perform differential switch to which it is associated.

Compact device, which is installed as a circuit breaker. Needless to make interconnections between the engine and the differential switch.

To protect high sensitivity mode reclosing insulation is used, the device measures the insulation periods of 3, 20 and 180 seconds: so that the computer only reconnects when the defect that caused the trip has disappeared.

Cancellation Possibility reconnection front engine mechanism that allows the ON / OFF. The team has locking system that determines the operation in manual or automatic (enabled reconnection) mode. Sealable.

The REC4 is a compact device that only occupies 3 modules and is installed as a differential switch. There is no need to interconnect between the motor and the differential switch.

Applications:

All those electrical installations where full continuity of electric service to unforeseen situations that cause tripping for reasons beyond the electrical insulation is needed.

• Housing Sector: refrigerators, alarms, garage doors, etc...
• Sector Services: air conditioning, refrigerators, lighting, SAIS, etc...
• Industry Sector: control of critical production processes.

Technical specifications:

• RCD Type: Class A
• Sensitivity, IAn: 30 mA
• Trip delay, tΔ: Instant
• Rated current In: 40 A
• Number of poles / voltage: 2 pole - 230 VAC
• Test: Built-in switch button
• Reset: mechanism on the front of the engine that allows the ON / OFF
• Number of reconnections: 3
• Time between reconnections: 3, 20, 180 s
• Reset time counter reconnections: 3, 20, 180 s
• Reconnection lockout output: Contact switched 230 VAC 130 mA
• Cancellation reconnection: Mechanism in the front of the engine that allows the ON / OFF.
• Sealable.
• Mounting: Fixing DIN 46277 (EN 50022)
• Degree of protection: IP 40
• Built according to the standards IEC 61008-1, EN 50557

Model. CIRCUTOR REC4-2P-40-30 (P26A21)

Resettable circuit breaker 2-pole Class A, 40 amp, 30 milliamps (2Px40Ax30mA). Suitable for domestic, commercial and industrial use.

Specifications:

• Built according to the UNE-EN61008-1 standard and RoHS compliance
• Breaking capacity 10 kA (10.000A)
• Rated operational voltage AC 230 V
• Test button "Test"

This resettable differential ensures continuity of electricity supply to avoid economic losses and has the following characteristics:

• Possibility of remote control.
• Programming the number of resets and time between resets.
• Read displayed the number of shots fired.
• Suitable for single and three phase installations.

Reference. CHINT RE-NL1-2-40-30A

Technical Characteristics:

• Number of Poles: 4 Poles
• Neutral pole position: Left
• Composition signaling contacts: 1 NO or 1NC flashing 1Hz
• [In] rated current: 40 A
• Earthing system TN-S TT
• Earth leakage sensitivity: 30 mA
• Location device system: Departure
• Rated operating frequency: 50 Hz
• [Ue] aisgnada voltage: 230 V AC 50 Hz phase to neutral
• Reset: Reset earth leakage faults
• Test function: Manual 100 V
• Protec.pérdida ground delay time: Instant
• Type earth leakage protection: Class A
• Leakage resistance 10 kOhm
• Cutting capacity and nominal fechamento: IDM 630 to 230 V
• [Ui] rated insulation voltage: 500 V
• [Uimp] rated impulse voltage: 4 kV
• Control Type: Lever
• Local signs: 2 LEDs, reset switch indication ON / OFF, Residual Current Device indication: ON / OFF.
• Adjustment Type: Control presence of insulation failure, No. Max consecutive restart Minimum interval between 2 locks, No. operations rearmament Reconeción, Cycle Reset, Restart if I fail transient isolation and arrest attachment cycle reset if fault isolation present.
• Signalling circuit voltage: DC: 5 ... 230 V - CA: 5 ... 230 V
• Mounting mode Fixed
• Mounting options: DIN rail 35mm
• Steps 9 mm 8
• Mechanical endurance: 1000 cycles open-close
• Standards: EN 61008 - IEC 61008
• IP Grade: IP20

Reference. SCHNEIDER 18266

Differential 4P, 40A, 30 mA, with automatic reconnection REC 4 series, to ensure continuity of electric service to unforeseen situations that cause tripping.

A circuit breaker associated with an intelligent engine reconnection, which enables safe reconnection to perform differential switch to which it is associated.

Compact device, which is installed as a circuit breaker. Needless to make interconnections between the engine and the differential switch.

To protect high sensitivity mode reclosing insulation is used, the device measures the insulation periods of 3, 20 and 180 seconds: so that the computer only reconnects when the defect that caused the trip has disappeared.

Cancellation Possibility reconnection front engine mechanism that allows the ON / OFF. The team has locking system that determines the operation in manual or automatic (enabled reconnection) mode. Sealable.

Applications:

All those electrical installations where full continuity of electric service to unforeseen situations that cause tripping for reasons beyond the electrical insulation is needed.

• Housing Sector: refrigerators, alarms, garage doors, etc...
• Sector Services: air conditioning, refrigerators, lighting, SAIS, etc...
• Industry Sector: control of critical production processes.

Technical specifications:

• RCD Type: Class A
• Sensitivity, IAn: 30 mA
• Trip delay, tΔ: Instant
• Rated current In: 40 A
• Number of poles / voltage: 4 pole - 230 VAC / 400 Vc.a.
• Test: Built-in switch button
• Reset: mechanism on the front of the engine that allows the ON / OFF
• Number of reconnections: 3
• Time between reconnections: 3, 20, 180 s
• Reset time counter reconnections: 3, 20, 180 s
• Reconnection lockout output: Contact switched 230 VAC 130 mA
• Cancellation reconnection: Mechanism in the front of the engine that allows the ON / OFF.
• Sealable.
• Mounting: Fixing DIN 46277 (EN 50022)
• Degree of protection: IP 40
• Built according to the standards IEC 61008-1, EN 50557

Model. CIRCUTOR REC4-4P-40-30 (P26F21)

Resettable circuit breaker 4-pole Class A, 40 amp, 30 milliamps (4Px40Ax30mA). Suitable for domestic, commercial and industrial use.

Specifications:

• Built according to the UNE-EN61008-1 standard and RoHS compliance
• Breaking capacity 10 kA (10.000A)
• Rated operational voltage AC 230 V
• Test button "Test"

This resettable differential ensures continuity of electricity supply to avoid economic losses and has the following characteristics:

• Possibility of remote control.
• Programming the number of resets and time between resets.
• Read displayed the number of shots fired.
• Suitable for single and three phase installations.

Reference. CHINT RE-NL1-4-40-30A

Resettable circuit breaker 4-pole Class A, 40 amp, 300 milliamps (4Px40Ax300mA). Suitable for domestic, commercial and industrial use.

Specifications:

• Built according to the UNE-EN61008-1 standard and RoHS compliance
• Breaking capacity 10 kA (10.000A)
• Rated operational voltage AC 230 V
• Test button "Test"

This resettable differential ensures continuity of electricity supply to avoid economic losses and has the following characteristics:

• Possibility of remote control.
• Programming the number of resets and time between resets.
• Read displayed the number of shots fired.
• Suitable for single and three phase installations.

Reference. CHINT RE-NL1-4-40-300A

SUPERIMMUNIZED Rearmable Differential with 3 resets composed of an automatic recloser plus a 2P, 40A, 30 mA (2x40x30 mA) superimmunized differential from Werden. The size of the recloser is only 1 module, so the total size will be 3 modules.

The superimmunized differentials guarantee the correct functioning and operation in the face of problems that are present in LV distribution systems, such as: networks disturbed by atmospheric surges (lightning), motor start-ups, high-power voltage and high-grade components harmonicas, among others.

When the differential is skipped, the automatic recloser will reconnect it for the first time at 10 seconds, for the second time at 60 seconds and finally at 300 seconds. If this third reconnection is not effective, it will not reconnect, understanding that there is a line failure. Once this is solved, it can be reconnected manually.

This Resettable differential allows maximum safety and continuity of service, thanks to its innovative insulation control system, the resettable differential reclosers allow reconnecting in conditions of optimal safety for people, both in residential and tertiary applications.

In the event of a differential trip (storms, humidity, sympathetic trip, etc.), the automatic recloser will reconnect the installation only if the defect has disappeared, guaranteeing the safety of people and the installation.

Recloser Technical Characteristics:

• 3.0 Nm tightening torque.
• Quick installation on 35mm DIN rail (IEC 60715).
• 3 resets (10, 60, 300 seconds and blocking).
• Automatic and manual reconnection.
• LED indicator.
• Mechanical life 6000 cycles.
• Electrical life 4000 cycles.

Differential Technical Characteristics:

• 6 kA short-circuit resistance (breaking capacity).
• Built according to IEC 61008-1 standard.
• Connection capacity 25 mm.
• 2.0 Nm tightening torque.
• Quick installation on 35mm DIN rail (IEC 60715).
• Local status signaling.
• Protection against earth leakage, current leakage and isolation function.
• High resistance to short circuits.
• AC and type A sensitivity.
• Nominal insulation voltage Ui 440V.
• Nominal impulse withstand voltage Uiamp 4kV.
• Allows the use of pin and fork type connection combs.
• Resistance of the electromechanical components 4000 operating cycles.
• Compatible with standard busbars.
• Test button "Test".