DPS + POP combined surge protection device against transient and permanent overvoltages Transient Type 2 - 4-pole Class II (4P) in 4 40 kA module.

DPS + POP combined surge protection device against transient and permanent overvoltages Transient Type 2 - 4-pole Class II (4P) in 4 40 kA module.

With the CIRPROTEC V-CHECK 4RPT, the installation is protected against transient voltage peaks and against permanent voltage surges. Typically, the former are associated with the lightning phenomenon and the latter with the bad connection / breakdown of the three-phase installation neutral.

This product has a high transient overvoltage discharge capacity and is ideal for industrial and tertiary installations.

Technical characteristics of the CIRPROTEC V-CHECK 4RPT - 77706415

• Certifications: CE
• Housing Color: Gray RAL 7035
• Degree of enclosure protection: IP 20
• Temperature range: -5 ° C ... +40 ° C

Transient Surge Protector (SPD)

• Classification according to EN 61643-11: Type 2
• Classification according to IEC 61643-11: Class II
• Maximum operating voltage AC (L-N) -Uc (L-N): 400 V
• Maximum operating voltage AC (N-PE) -Uc (N-PE): 255 V
• Maximum discharge current (8/20) (L-N) -Imax (L-N): 40 kA
• Rated discharge current (8/20) (L-N) -In (L-N): 15 kA
• Level of protection in tension (L-N) -Up (L-N): ≤ 1,8 kV
• Voltage protection level (N-PE) -Up (N-PE): ≤ 1,8 kV
• Short-circuit capacity-Icc: 25 kA
• Response Time (L-N) -tA: 25 ns
• Response time (N-PE) -tA: 100 ns
• Final visual indication of life: Yes
• Thermal dynamic shut-off (L-N): Y

Permanent Surge Protector (POP)

• Method of action: Maximum coil or emission
• Rated voltage AC 50 Hz (L-N) -Un (L-N): 230 V
• Rated voltage AC 50 Hz (L-L) -Un (L-L): 400 V
• Test Button: Yes
• Maximum actuation time-tA [Ua = 255 V]: No tripping / No tripping
• Minimum non-response time-tA [Ua = 255 V]: No tripping / No tripping
• Maximum actuation time-tA [Ua = 275 V]: 15 s
• Minimum non-response time-tA [Ua = 275 V]: 3 s
• Maximum actuation time-tA [Ua = 300 V]: 5 s
• Minimum non-response time-tA [Ua = 300 V]: 1 s
• Maximum actuation time -tA [Ua = 350 V]: 0.75 s
• Minimum non-response time-tA [Ua = 350 V]: 0.25 s
• Maximum actuation time-tA [Ua = 400 V]: 0.20 s
• Minimum non-response time-tA [Ua = 400 V]: 0.07 s
• Torque: 4 Nm
• Rigid bare cable: 10 mm
• Minimum section of rigid conductor: 6 mm²
• Maximum section of rigid conductor: 35 mm²
• Flexible stripped cable: 10 mm
• Minimum section of flexible conductor: 6 mm²
• Maximum section of flexible conductor: 25 mm²

​Reference. CIRPROTEC V-CHECK 4RPT - 77706415

The discount applied to the PVP is -22%

Transient 2-Pole Surge Protector (1P + N) 15 kA, for single-phase installations.

This device protects the installation of transient surges caused by lightning strikes or mains switching, preventing it from affecting installed equipment.

Technical characteristics:

• 1 Pole + Neutral Type II transient overvoltage protector -15 kA
• Class C
• Maximum discharge current (Imáx) 30 kA
• Protection level Up <1.2 kV
• Uc (VAC) 275
• Maximum working voltage Uc 360 V
• Visual status indicator

​Reference. WERDEN WE-9220

The discount applied to the PVP is -60%

This device protects the system from transient overvoltages caused by lightning strikes or switching network, preventing it from affecting the equipment installed.

Built according to UNE 61643-1 and RoHS compliance regulations.

Technical Characteristics:

• 1 Pole x 40 A Type II Transient Surge Protector
• Impulse current (Iimp) 20 kA
• Maximum discharge current (Imax) 40 kA
• Up Protection level <1.2 kV
• Response time <25 ns
• Maximum working voltage Uc 275 V
• Visual status indicator.

Reference. WE-9200 WERDEN

The discount applied to the PVP is -60%

This device protects the system from transient overvoltages caused by lightning strikes or switching network, preventing it from affecting the equipment installed.

Built according to UNE 61643-1 and RoHS compliance regulations.

Technical Characteristics:

• 2 Pole x 40 A type II transient overvoltage protector
• Impulse current (Iimp) 20 kA
• Maximum discharge current (Imax) 40 kA
• Up Protection level <1.8 kV
• Response time <25 ns
• Maximum working voltage Uc 440 V
• Visual status indicator.

Reference. WERDEN WE-9215

The discount applied to the PVP is -60%

Transient surge protector type I and II of 1 Pole + Neutral (1P + N) 20 kA, for single-phase installations. Suitable for centralizing meters according to ENDESA's UNE-EN 61643-11: 2013 (IEC 61643-1: 2011) standard of June 14, 2019 and IBERDROLA's NI-42,71,01 standard.

This device protects the installation from transient overvoltages, caused by lightning strikes or network switches, preventing it from affecting the installed equipment.

Technical characteristics:

• Poles: 1 + N
• Class: Type 1+2
• Maximum voltage Uc (L-N): 275V
• Maximum voltage Uc (N-PE): 255V
• Impulse Current Iimp (10 / 350µs) (L-N): 12.5 kA
• Impulse Current Iimp (10 / 350µs) (N-PE): 25 kA
• Nominal current In (8 / 20µs) (L-N): 20 kA
• Nominal current In (8 / 20µs) (N-PE): 25 kA
• Maximum Current Imax (L-N): 50 kA
• Maximum Current Imax (N-PE): 100 kA
• Protection voltage Up: ≤1.5
• Protection voltage Up <5kV: ≤1.3
• Response time: ≤25 ns
• Operating temperature: -40° C-80°
• Operating status / Fault indication: Green / Red
• Minimum connection section: 6 mm²
• Maximum connection section: 35 mm²
• Mounting: DIN rail
• Degree of protection: IP 20
• Enclosure Material: UL94-V0 Thermoplastic
• UNE-EN 61643-11: 2013 (IEC 61643-1: 2011)

​Reference. WERDEN WE-9392

The discount applied to the PVP is -60%

Transient surge protector type I and II of 1 Pole + Neutral (1P + N) 20 kA, for single-phase installations. Suitable for centralizing meters according to ENDESA's UNE-EN 61643-11: 2013 (IEC 61643-1: 2011) standard of June 14, 2019 and IBERDROLA's NI-42,71,01 standard.

This device protects the installation from transient overvoltages, caused by lightning strikes or network switches, preventing it from affecting the installed equipment.

Technical characteristics:

• Poles: 1 + N
• Class: Type 1+2
• Maximum voltage Uc (L-N): 275V
• Maximum voltage Uc (N-PE): 255V
• Impulse Current Iimp (10 / 350µs) (L-N): 12.5 kA
• Impulse Current Iimp (10 / 350µs) (N-PE): 12.5 kA
• Nominal current In (8 / 20µs) (L-N): 25 kA
• Nominal current In (8 / 20µs) (N-PE): 50 kA
• Maximum Current Imax (L-N): 50 kA
• Maximum Current Imax (N-PE): 100 kA
• Protection voltage Up: ≤2
• Protection voltage Up <5kV: ≤1.3
• Response time: ≤25 ns
• Operating temperature: -40° C-80°
• Operating status / Fault indication: Green / Red
• Minimum connection section: 6 mm²
• Maximum connection section: 35 mm²
• Mounting: DIN rail
• Degree of protection: IP 20
• Enclosure Material: UL94-V0 Thermoplastic
• UNE-EN 61643-11: 2013 (IEC 61643-1: 2011)

​Reference. WERDEN WE-9390

The discount applied to the PVP is -60%

This device protects the installation from transient overvoltages, caused by lightning strikes or network switching, preventing it from affecting the installed equipment.

Built according to the UNE-61643-1 standard and complying with the RoHS regulations.

Technical characteristics:

• Transient overvoltage protector type II of 3 Poles + N
• Standard: IEC 61643-11:2011
• Rated voltage: 230/400 V~
• Maximum continuous operating voltage: 275 V~
• Protection level (Up): ≤1.5 kV
• Rated discharge current (In): 20 kA
• Peak current (Imax): 40 kA
• Response time: <25
• DIN rail 35mm
• Protection: IP20
• Material: Thermoplastic UL94-V0
• Working temperature: -40ºC ~ 85ºC
• Relative humidity: ≤95% (25ºC)

Reference. WERDEN WE-9237

The discount applied to the PVP is -60%

Transient overvoltage protector type I and II, 3 Poles + Neutral (3P + N) 20 kA, for three-phase installations. Suitable for centralizing meters according to ENDESA's UNE-EN 61643-11: 2013 (IEC 61643-1: 2011) standard of June 14, 2019 and IBERDROLA's NI-42,71,01 standard.

This device protects the installation from transient overvoltages, caused by lightning strikes or network switches, preventing it from affecting the installed equipment.

Technical characteristics:

• Poles: 3 + N
• Class: Type 1+2
• Maximum voltage Uc (L-N): 275V
• Maximum voltage Uc (N-PE): 255V
• Impulse Current Iimp (10 / 350µs) (L-N): 12.5 kA
• Impulse Current Iimp (10 / 350µs) (N-PE): 25 kA
• Nominal current In (8 / 20µs) (L-N): 20 kA
• Nominal current In (8 / 20µs) (N-PE): 25 kA
• Maximum Current Imax (L-N): 50 kA
• Maximum Current Imax (N-PE): 100 kA
• Protection voltage Up: ≤1.5
• Protection voltage Up <5kV: ≤1.3
• Response time: ≤25 ns
• Operating temperature: -40° C-80°
• Operating status / Fault indication: Green / Red
• Minimum connection section: 6 mm²
• Maximum connection section: 35 mm²
• Mounting: DIN rail
• Degree of protection: IP 20
• Enclosure Material: UL94-V0 Thermoplastic
• UNE-EN 61643-11: 2013 (IEC 61643-1: 2011)

​Reference. WERDEN WE-9393

The discount applied to the PVP is -60%

Transient overvoltage protector type I and II, 3 Poles + Neutral (3P + N) 25 kA, for three-phase installations. Suitable for centralizing meters according to ENDESA's UNE-EN 61643-11: 2013 (IEC 61643-1: 2011) standard of June 14, 2019 and IBERDROLA's NI-42,71,01 standard.

This device protects the installation from transient overvoltages, caused by lightning strikes or network switches, preventing it from affecting the installed equipment.

Technical characteristics:

• Poles: 3 + N
• Class: Type 1+2
• Maximum voltage Uc (L-N): 275V
• Maximum voltage Uc (N-PE): 255V
• Impulse Current Iimp (10 / 350µs) (L-N): 25 kA
• Impulse Current Iimp (10 / 350µs) (N-PE): 100 kA
• Nominal current In (8 / 20µs) (L-N): 25 kA
• Nominal current In (8 / 20µs) (N-PE): 100 kA
• Maximum Current Imax (L-N): 50 kA
• Maximum Current Imax (N-PE): 100 kA
• Protection voltage Up: ≤2
• Protection voltage Up <5kV: ≤1.3
• Response time: ≤100 ns
• Operating temperature: -40° C-80°
• Operating status / Fault indication: Green / Red
• Minimum connection section: 10 mm²
• Maximum connection section: 35 mm²
• Mounting: DIN rail
• Degree of protection: IP 20
• Enclosure Material: UL94-V0 Thermoplastic
• UNE-EN 61643-11: 2013 (IEC 61643-1: 2011)

​Reference. WERDEN WE-9391

The discount applied to the PVP is -60%

Permanent overvoltage protector with nominal voltage AC 230V and disconnection of minimum voltage 170V and disconnection of maximum voltage 280V.

This permanent overvoltage protector is compatible with the entire range of WERDEN 2-pole circuit breakers (from 10A to 63A single-phase 6kA).

Technical characteristics:

• Voltage (Ue): 230V
• Desc. max. voltage: 270V ±5%
• Desc. min. voltage: 170V ±5%
• Dec. time: 0.1 s
• Test button: Yes
• Reset button: Yes
• DIN rail IEC/EN 60715
• Electromechanical duration: ≥ 4000 cycles
• Protection: IP20
• Outer insulation material: PC/PA
• Fire resistance: V0
• Temp. working: -40 ~ +85
• Relative humidity: ≤95%(25ºC)

​Reference. WERDEN WE-9230

The discount applied to the PVP is -60%